您好,欢迎访问旭达流体网站!  服务热线:400-9921-168  繁体中文
 
关于我们|新闻动态|产品展示|营销网络|客服中心|人才中心|会员中心|电子样本|HTML版|网站导航  

 
今天是
企业新闻  行业新闻
新闻动态
产品搜索:
流量计算
上一篇:我们公司网站全新改版发布时间:2008/10/12 9:21:39
来自:旭达流体
下一篇:常用阀门标准
字体颜色:    【字体:放大 正常 缩小】 【双击鼠标左键自动滚屏】

如何使用流量系数
How to use Cv

  法门流量系数(Cv)是表示阀门通过流体能力的数值。Cv越大,在给定压降下阀门能够通过的流体就越多。Cv值1表示当通过压降为1 PSI时,阀门每分钟流过1加仑15oC的水。Cv值350表示当通过压降为1 PSI时,阀门每分钟流过350加仑15oC的水。
  Valve coefficient (Cv) is a number which represents a valve's ability to pass flow. The bigger the Cv, the more flow a valve can pass with a given pressure drop. A Cv of 1 means a valve will pass 1 gallon per minute (gpm) of 60oF water with a pressure drop (dp) of 1 PSI across the valve. A Cv of 350 means a valve will pass 350 gpm of 60oF water with a dp of 1 PSI.

公式1
FORMULA 1

  流速:磅/小时(蒸汽或水)
  FLOW RATE LBS/HR (Steam or Water)

  

在此:
Where:
dp=压降,单位:PSI
dp=pressure drop in PSI
F=流速,单位:磅/小时
F=flow rate in lbs./hr.
=比容积的平方根,单位:立方英尺/磅
(阀门下游)
=square root of a specific volume in ft3/lb.
(downstream of valve)

公式2
FORMULA 2

  流速:加伦/分钟(水或其它液体)
  FLOW RATE GPM (Water or other liquids)

  

在此:
Where:
dp=压降,单位:PSI
dp=pressure drop in PSI
Sg=比重
Sg=specific gravity
Q=流速,单位:加伦/分钟
Q=flow rate in GPM

局限性
LIMITATIONS

  上列公式在下列条件下无效:
  Above formulas are not valid under the following conditions:

  1. 对于可压缩性流体,如果压降超过进口压力的一半。
    For compressible fluids, where pressure drop exceeds half the inlet pressure.
  2. 对于不可压缩性流体,如果压降产生空穴或闪蒸。
    For non-compressible fluids, where pressure drop causes cavitation or flashing.
  3. 对于双相流体,如蒸汽-水混合流体。
    For dual-phase flow such as steam-water mixtures.

例子
EXAMPLE

  1. 通过DN350, 压力等级Class 900的压力密封闸阀,水温400oF,压力为1500 PSIG,流速为5,000,000磅/小时的压降是多少?
    What is the pressure drop through a 14" Class 900 pressure seal gate valve with 400oF water, 1500 PSIG, and 5,000,000 lbs/hr flow rate?
    解:采用公式1
    Solution: Use formula 1.
F=5,000,000
=0.137 (从水温为400oF的表中得到)
=0.137 (from chart for water at 400oF)
Cv=9150 (来自本页)
Cv=9150 (from page 26)

 
  1. DN350 x DN300 x DN350,压力等级Class 900缩喉管压力密封闸阀,其它条件与例1相同,求压降。
    What is the pressure drop through a 14"x12"x14" Class 900 Venturi pressure seal gate valve with the same conditions as example 1.
    解:采用公式1
    Solution: Use formula 1.
    Cv = 6285 (来自本页)
    Cv = 6285 (from page 26)
  2. 温度900oF, 压力1200 PSI,流速500,000磅/小时的蒸汽应用中压降小于5 PSI的压力等级Class 2500闸阀的最小通径是多少?
    What is the smallest Class 2500 gate valve that will have less than a 5 PSI pressure drop in 900oF, 1200 PSI steam service at a flow rate of 500,000 lbs/hr?
    解:采用公式1
    Solution: Use formula 1.
F=500,000
=0.785 (来自900oF, 1200 PSIG蒸汽表)
=0.785 (from chart for steam at 900oF, 1200 PSIG)
= = 2.24
 

  最接近的、较大的Cv是DN250压力等级Class 2500闸阀,其Cv是3130。这里是压降小于5 PSIG的最小的阀门。
  The closest higher Cv is a 10" Class 2500 gate with a Cv of 3130. This is the smallest valve with a pressure drop less than 5 PSIG.

水和蒸汽的备选特性
Selected Properties of Water and Steam
水的(下游)
For Water (Downstream)
所有压力等级
All
Pressures
温度(oF)
Temperature (oF)
100200300400500600
0.1270.1290.1320.1370.1430.154
 
蒸汽的(下游)
For Steam (Downstream)
压力
PSIG
Pressure
PSIG
温度(oF)
Temperature (oF)
Sat50060070080090010001100
100
200
300
400
500
600
700
800
900
1000
1100
1200
1300
1400
1600
1800
2000
2500
3000
4000
5000
6000
1.97
1.46
1.21
1.06
0.950
0.865
0.801
0.747
0.701
0.662
0.628
0.598
0.570
0.545
2.20
1.61
1.30
1.11
0.979
0.895
2.32
1.68
1.38
1.19
1.06
0.960
0.880
0.815
0.759
0.710
0.670
0.629
0.590
0.559
2.44
1.77
1.46
1.26
1.12
1.02
0.941
0.875
0.821
0.773
0.732
0.695
0.662
0.633
0.58
0.54
0.50
0.41
0.31
0.17
0.16
0.16
2.54
1.85
1.52
1.32
1.18
1.08
0.994
0.926
0.870
0.816
0.781
0.745
0.710
0.683
0.63
0.59
0.55
0.48
0.42
0.32
0.24
0.19
2.64
1.95
1.60
1.38
1.23
1.13
1.04
0.972
0.914
0.865
0.823
0.785
0.752
0.723
0.67
0.63
0.59
0.52
0.46
0.38
0.32
0.28
2.74
2.00
1.65
1.43
1.28
1.17
1.08
1.01
0.955
0.917
0.872
0.813
0.789
0.752
0.70
0.66
0.62
0.55
0.49
0.42
0.36
0.32
2.84
2.07
1.71
1.47
1.33
1.22
1.12
1.05
0.99
0.94
0.90
0.86
0.83
0.79
0.74
0.69
0.65
0.58
0.52
0.44
0.39
0.35

阀座端口流速计算
Calculating Seat Port Velocity

  下列公式可以用来计算任何阀门的阀座流速:
  The following formulas can be used to calculate seat port
velocity in any valve:

流量(磅/小时): 流速: (英尺/秒)=
F()2
25A
Flow (lbs/hr): vel: (fps) =
F()2
25A
流量(加仑/分钟): 流速: (英尺/秒)=
0.32Q
A
Flow (GPM): vel: (fps) =
0.32Q
A

 

在此:
Where:
F=流量(磅/小时)
F=flow (lbs/hr)
=比容积的平方根
=square root of specific volume
A=阀座端口面积 (英寸2)
A=seat port area (in2)
Q=流量 (加仑/分钟)
Q=flow (gpm)

例:
  DN300型号58809 (压力等级Class 900)止回阀,流体介质为温度500 oF,压力200 PSIG的蒸汽,流速为90,000磅/小时,求阀座端口的流速?
Example:
  What is the seat port velocity in a 12" Figure 58809 (Class 900) check valve with a flow rate of 90,000 lbs/hr of steam at 500 oF and 200 PSIG?

解:
  从蒸汽表得为1.61,从阀座端口面积表A得阀座端口面积为78.5英寸2
Answer:
  From the steam tables is 1.61, and from the seat port area table A is 78.5 in2.

流速: (英尺/秒)=
F()2
25A
=
90,000 (1.61)2
25 (78.5)
= 118.8 英尺/秒
Vel (fps) =
F()2
25A
=
90,000 (1.61)2
25 (78.5)
= 118.8 fps

例:
  DN300型号180 (压力等级150)旋启式止回阀,流体介质为温度500oF,压力200 PSIG的蒸汽,流速为90,000磅/小时,求阀座端口流速?
Example:
  What is the seat port velocity in a 12" Figure 180 (Class 150) Swing Check Valve with a flow rate of 90,000 lbs/hr of steam at 500oF and 200 PSIG?

解:
  查表得为1.61,A为 113.1英寸3.
Answer:
  From the tables is 1.61 and A is 113.1 in3.

流速: (英尺/秒)=
F()2
25A
=
90,000 (1.61)2
25 (113.1)
= 82.5英尺/秒
Vel (fps) =
F()2
25A
=
90,000 (1.61)2
25 (113.1)
= 82.5 fps

局限性
LIMITATIONS

  流速公式在下列条件下无效:
  Velocity formulas are not valid under the following conditions:

  1. 对于可压缩性流体,如果压降超过进口压力的一半。
    For compressible fluids, where pressure drop exceeds half the inlet pressure.
  2. 对于不可压缩性流体,如果压降产生空穴或闪蒸。
    For non-compressible fluids, where pressure drop causes cavitation or flashing.
  3. 对于双相流体,如蒸汽-水混合流体。
    For dual-phase flow such as steam-water mixtures.

注意
NOTE

  在确定止回阀通径时,最适宜的工作流速应该位于这些范围内:
  When determining sizing for check valves, the optimum operating velocities should fall within these ranges:

BB旋启式止回阀:55 至115或135至240
BB截止止回阀:40 至120
PS提升式阀瓣止回阀:55至200
PSY形止回阀:148 至200
BB Swing Check Valves - 55 to 115 or 135 to 240
BB Stop Check Valves - 40 to 120
PS Tilt Disc Check Valves - 55 to 200
PS Stop Check Valves - 40 to 180
PS Y- Stop Check Valves - 148 to 200

 
阀座端口面积“A”(英寸2)
适用于螺栓阀帽阀门
SEAT PORT AREA "A" FOR BOLTED
BONNET VALVES (in2)
阀门通径
Valve Size
压力等级
Pressure Class
1503006009001500
11/2
2
21/2
3
4
6
8
10
12
14
16
18
20
24
30
36
1.8
3.1
4.9
7.1
12.6
28.3
50.3
78.5
113.1
137.9
182.7
233.7
291.0
424.5
671.9
969.0
1.8
3.1
4.9
7.1
12.6
28.3
50.3
78.5
113.1
137.9
182.7
227.0
283.5
424.5
672.0
942.0
1.8
3.1

7.1
12.6
28.3
48.7
74.7
108.4
130.2
170.9
213.8
261.6
380.1
590.9
851.2
1.8
3.1
4.9
6.5
11.8
26.0
44.2
71.0
100.0
117.9





1.5
2.8
4.0
6.0
10.3
22.7
38.5
60.0
84.5
101.6





 

阀座端口面积(英寸2)
适用于压力密封闸阀,截止阀,提升式阀瓣止回阀
SEAT PORT AREA FOR PRESSURE SEAL GATE,
GLOBE, TILT DISC CHECK VALVES (in2)

阀门通径
Valve Size
压力等级
Pressure Class
60090015002500
21/2
3
4
6
8
10
12
14
16
18
20
24
5.4
5.4
9.6
23.2
39.9
61.0
88.7


173.8

310.25
5.9
5.9
10.3
21.7
37.7
58.4
80.5
97.2
125.2
156.7
198.0
287.3
3.3
4.9
8.3
18.9
31.9
48.7
69.0
82.5
108.4
137.9
170.9
247.5
2.4
3.6
5.9
12.6
21.7
34.5
47.2
58.2
76.6
97.2
117.9
170.9

 

阀座端口面积(英寸2)
适用于压力密封Y形截止阀
SEAT PORT AREA FOR PRESSURE SEAL Y-GLOBE
VALVES (in2)

阀门通径
Valve Size
压力等级
Pressure Class
90015002500
8
10
12
14
16
18
20
24
39.9
61.9
86.6
86.6
135.4
135.4
198.1
302.6
39.9
61.9
86.6
86.6
135.4
135.4
198.1
302.6
27.2
42.8
60.1
86.6
86.6
135.4
135.4
198.1
螺栓阀帽闸阀全开状态下的流量系数Cv
Bolted Bonnet
Gate Valves FULL OPEN Cv
阀门通径
Valve Size
压力等级
Pressure Class
1503006009001500
11/2
2
21/2
3
4
5
6
8
10
12
14
16
18
20
24
30
36
165
307
490
710
1300
2090
3110
5720
8935
13350
16275
21560
28720
35760
52165
86235
129500
165
307
490
710
1300

3110
5720
8935
13350
16275
21560
27890
34840
51050
84765
125825
165
307
490
710
1300

3110
5540
8495
12800
15370
29170
26270
32140
46710
75530
114250



650
1220

2850
5025
7850
11475
13910





138
270
400
600
1070
1600
2500
4375
6840
9980
12000





 
图1
螺栓阀帽截止阀
Figure 1
Bolted Bonnet
Globe Valves

(1)当开启度小于
10%时,不建议
用于节流应用。
(1) not recommended for
throttling at less
than 10% Open.

 

压力密封闸阀全开状态下的流量系数Cv
Pressure Seal
Gate Valves FULL OPEN Cv

阀门通径
Valve Size
压力等级
Pressure Class
60090015002500
21/2
3
4
6
8
10
12
14
16
18
20
24
350
525
925
2150
3775
5750
8600
10275
13425
17200
20950
30850
350
450
850
1925
3575
5250
7550
9150
11950
15575
19200
27675
275
415
730
1675
2925
4550
6570
7890
10325
13425
16825
24150
190
275
460
1100
1970
3130
4535
5500
7210
9215
11450
16575

 

压力密封缩喉管闸阀全开状态下的流量系数Cv
Pressure Seal
Venturi Gate Valves FULL OPEN Cv

阀门通径
Valve Size
压力等级
Pressure Class
60090015002500
8 x 6 x 8
10 x 8 x 10
12 x 10 x 12
14 x 12 x 14
16 x 14 x 16
18 x 16 x 18
20 x 18 x 20
22 x 20 x 22
26 x 24 x 26
1570
2795
4485
7310
9000
11000
14200
16800
25000
1385
2385
4065
6285
7200
9760
12185
16005
23000
1185
2155
3450
5640
6270
8465
11120
14130
815
1430
2515
3855
4415
6165
7960
9645
 
螺栓阀盖旋启式止回阀全开状态下的流量系数Cv
Bolted Cap
Swing Check Valves FULL OPEN Cv
阀门通径
Valve Size
压力等级
Pressure Class
1503006009001500
11/2
2
21/2
3
4
6
8
10
12
14
16
18
20
24
30
63
142
217
356
716
1414
2961
5720
7860
10416
13800
13420
16708
33384
54556
63
168
275
392
740
1992
2340
5720
8544
19464
13800
13029
16276
36672
54652
97
139
227
246
499
1334
3359
5440
7045
9840
12912

19540




358
605
1623
2508
4069
6316






111

315
564
1520








 

螺栓阀帽截止阀全开状态下的流量系数Cv
Bolted Bonnet
Globe Valves FULL OPEN Cv

阀门
通径
Valve Size
压力等级
Pressure Class
150300600900
塞形

球形
阀瓣
Plug or
Ball
Disc
V形
端口
阀瓣
V-Port
Disc
塞形

球形
阀瓣
Plug or
Ball
Disc
V形
端口
阀瓣
V-Port
Disc
塞形

球形
阀瓣
Plug or
Ball
Disc
V形
端口
阀瓣
V-Port
Disc
塞形

球形
阀瓣
Plug or
Ball
Disc
11/2
2
21/2
3
4
5
6
8
10
12
23
43
70
100
185
297
440
810
1260
1890

40

92
170
273
405
745
1150
23
43
70
100
185

440
810
1260
1890
21
40

92
170

405
745

23
43
70
100
185

440
780

1810

40

92
170

405





90
170




 

压力密封提升式阀瓣止回阀全开状态下的流量系数Cv
Pressure Seal
Tilting Disc Check Valves FULL OPEN Cv

阀门通径
Valve Size
压力等级
Pressure Class
90015002500
21/2
3
4
6
8
10
12
14
16
18
20
24
95
146
268
627
1062
1722
2420
2955
3945
4900
6275
9295
80
132
230
536
940
1465
2110
2550
3395
4365
5465
8060
60
94
146
355
627
1020
1420
1775
2355
3025
3705
5465

 

压力密封缩喉管提升式阀瓣止回阀全开状态下的流量系数Cv
Pressure Seal
Venturi Tilting Disc Check Valves FULL OPEN Cv

阀门通径
Valve Size
压力等级
Pressure Class
150300600
8 x 6 x 8
10 x 8 x 10
12 x 10 x 12
14 x 12 x 14
16 x 14 x 16
18 x 16 x 18
20 x 18 x 20
22 x 20 x 22
565
955
1550
2175
2660
3550
4410
5650
480
845
1320
1900
2295
3055
3930
4920
320
565
920
1275
1598
2120
2725
3335

球形止回阀,截止止回阀,提升式止回阀的流量特性曲线
Characteristic Flow Curves for Globe Stop, Stop-Check, Lift-Check Valves

小于全开状态的估计流量系数Cv
Estimating Cv For Less Than Fully Open Valves


图2
球形止回阀,截止止回阀和提升式止回阀
Figure 2
Globe Stop, Stop-Check and
Lift-Check Valves

压力密封T形球形止回阀,截止止回阀和提升式止回阀
阀全开状态下的流量系数Cv
Pressure Seal T-Globe Stop,
Stop-Check and Lift-Check Valves FULL OPEN Cv
阀门通径
Valve Size
压力等级
Pressure Class
90015002500
21/2
3
4
6
8
10
12
14
90
105
195
455
800
1250
1820
2205
65
95
170
395
695
1085
1580
45
65
105
265
470
750
1100

 

压力密封Y球形止回阀,截止止回阀和提升式止回阀
阀全开状态下的流量系数Cv
Pressure Seal Y-Globe Stop,
Stop-Check and Lift-Check Valves FULL OPEN Cv

阀门通径
Valve Size
压力等级
Pressure Class
60090015002500
8
10
12
14
16
18
20
24
2025
3025
4600
4300
7650
7325
11800
16450
1750
2725
3825
3650
6000
5825
9125
13500
1750
2725
3825
3650
6000
5825
9125
13500
1175
1875
2650
4075
3775
6625
6225
9050

  表中所列流量系数仅适用于全开状态下的阀门。不是全开状态的流量系数可以采用适用于提升式阀瓣止回阀和截止阀的流量特性曲线进行估算。不建议将闸阀用在节流应用中。
  The flow coefficient (Cv) listed in the tables apply to fully open valves only. Flow coefficients at other than fully open may be approximated by use of the characteristic flow curves for tilting disc check and globe valves. Gate valves are not recommended for throttling service.

例:
  DN300,压力等级Class 900的美国太平洋压力密封截止阀在开气度为1/4时的流量系数是多少?
EXAMPLE:
 

 


图3
Y形球形止回阀,截止止回阀和提升式止回阀
Figure 3
Y-Globe Stop, Stop-Check and
Lift-Check Valves

压力密封缩喉管球形止回阀,截止止回阀和提升式止回阀
阀全开状态下的流量系数Cv
Pressure Seal Venturi Globe Stop,
Stop-Check and Lift-Check Valves FULL OPEN Cv
阀门通径
Valve Size
压力等级
Pressure Class
90015002500
8 x 6 x 8
10 x 8 x 10
12 x 10 x 12
14 x 12 x 14
16 x 14 x 16
450
770
1215
1775
2125
390
690
1055
1550
260
465
745
1070

 

压力密封缩喉管Y球形止回阀,截止止回阀和提升式止回阀
阀全开状态下的流量系数Cv
Pressure Seal Venturi Y-Globe Stop,
Stop-Check and Lift-Check Valves FULL OPEN Cv

阀门通径
Valve Size
压力等级
Pressure Class
60090015002500
8 x 6 x 8
10 x 8 x 10
12 x 10 x 12
14 x 12 x 14
16 x 14 x 16
18 x 16 x 18
20 x 18 x 20
22 x 20 x 22
16 x 24 x 26
1100
1925
2875
4375
4075
7250
6950
11200
15850
1000
1675
2600
3650
3450
5700
5525
8675
12825
1000
1675
2600
3650
3450
5700
5525
8675
12825
650
1125
1775
2525
3875
3575
6300
5925
8600

解:
  从上列流量系数表中得到,DN300,压力等级Class 900截止阀在全开状态下的Cv是1820。
SOLUTION:
  From the flow coefficient table above, the fully open Cv for a 12 inch, Class 900 globe valve is 1820.

  查询图2,全开状态的1/4时阀门的比率是52%.
  Consulting Figure 2, the percent of fully open Cv at 1/4 valve open is 52%.

  因此计算1/4全开的流量系数Cv为:
  0.52 x 1820 = 946.
  The Cv at 1/4 open is then computed as:
  0.52 x 1820 = 946.

 
 
用户名:
   
密 码:



暂时没有招聘信息,如果您有意向加盟我们的团队,请填写应聘表!!
收货人姓名:

 
您最能接受的信息通知方式?
 电话联系通知
 手机信息通知
 订阅邮件通知
 
打印本页 关闭窗口
通讯地址:江苏省苏州市姑苏区虎池路1680号12幢     总机电话:4009921168     传真:4009921168-9    E-mail:xuda@fuqiufa.com 
苏ICP备16042488号  Copyright ©2006-2024 Xuda Fluid All rights reserved   法律声明
在线服务:
点击这里给我发消息或留言(销售部)点击这里给我发消息或留言(技术部)